Home

Scotch premium 3M 233+ - 18mm

3M 4251 A1P2 Mask

Masque 3M 4255 A2P2

Masque 3M 7502 A2P3

Masque 3M intégral 6800

6035 Dust Cartridges - 3M 7502 Mask

This range of trapezoidal gas and vapor filters combines excellent protection, comfort, and balance. Lightweight, low breathing resistance, and well-balanced when mounted on the mask. Provides an excellent field of vision due to its unique trapezoidal shape. The filters can be used on all 3M half and full face masks equipped with a bayonet fitting system, such as the 3M 7500 and 3M 6800. The bayonet system allows the filters to be attached with a click, simplifying installation.

Features

• Filters that protect against: Organic vapors (boiling point > 65°C)
• Standard: EN 141
• Can be combined with a dust filter

This range of trapezoidal gas and vapor filters combines excellent protection, comfort, and balance. Lightweight, low breathing resistance, and well-balanced when mounted on the mask. Provides an excellent field of vision due to its unique trapezoidal shape. The filters can be used on all 3M half and full face masks equipped with a bayonet fitting system, such as the 3M 7500 and 3M 6800. The bayonet system allows the filters to be attached with a click, simplifying installation.

Features

• Filters that protect against: Organic vapors (boiling point > 65 °C), inorganic vapors, acid gases, ammonia and its derivatives
• Standard: EN 141
• Can be combined with a dust filter

Aerialite Volan 7534 6oz Fiberglass - 80cm Width

The WoodKit PRO Mini Simmons was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Retro Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Flying Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO 7 Seas was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Dream Catcher was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Spitfire  was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO One Mid was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO The Tanker was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Nexpa was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Rocket was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Kanaloa was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Murcielago was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Malibu was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Mini Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Infinity was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Jiantou was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Spider was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Stiletto was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Basic includes everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- 8 planed Paulownia boards for the deck/bottom (150mm wide and 5mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

Optional:
- Plywood panels ( 5mm poplar ply or 5.5mm Surfply3L) for cutting out the frame
- CNC laser cutting of the skeleton from a 3D shape file

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Shape300 Gather everything you need to make your Hollow surfboard from Paulownia wood and make construction easier with the top/bottom panels already glued in 300mm.

It includes:

- 4 planed Paulownia boards for the deck/bottom (300mm wide and 5mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

Optional:
- Plywood panels ( 5mm poplar ply or 5.5mm Surfply3L) for cutting out the frame
- CNC laser cutting of the skeleton from a 3D shape file

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Custom Gather everything you need to make your Hollow surfboard from Paulownia wood and make construction easier with the top/bottom panels already glued in 600mm width.

It includes:

- The skeleton (FrameKit) laser-cut from your shape3D file using CNC technology
- Planed Paulownia panels for the deck/bottom (600mm wide and 6mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

A high-performance temporary fixing, specially designed for the implementation of carbon fibers.

CARBONtak™ is a high-performance aerosol adhesive that temporarily holds lightweight carbon fibers in place during the manufacturing of composite parts. It is particularly well-suited for producing natural-looking, unpainted carbon parts manufactured using the vacuum bagging process.

It ensures effective support of the fibers during the various preparation and implementation stages, while facilitating their positioning before impregnation with the resin.

Fast and effective adhesion for your temporary assemblies and fixings.

BAXT Universal Contact is a versatile, fast-drying aerosol contact adhesive designed to bond many lightweight materials and facilitate assembly and manufacturing operations.

Its fine mist spray allows for even, precise, and controlled application without excess glue. It offers rapid bonding and high-performance adhesion to a wide range of surfaces: paper, cardboard, fabrics, foams, plastics, metals, and wood.

Particularly suited to the composites industry, it provides an ideal solution for the temporary holding of reinforcement plies and dry materials during vacuum infusion operations.