Home

EON Foam 6'6"SB foam block molded in France (Brittany) unslatted.

What does biomass mean?
Made from NEOPS® polystyrene from KNAUF INDUSTRIES® , the naphtha from oil refining has been replaced by a plant-based naphtha from the compression of plants: public and private pruning, agricultural rotations, clearing, dead leaves, grass cuttings taken to the recycling center.
The foam is also 100% recyclable through the Knauf Circular reprocessing network.

The polystyrene beads are agglomerated in a mold close to the final shape under high pressure, allowing excellent compressive strength, low water and resin absorption during lamination and an easier sanding finish compared to conventional polystyrene in blocks.

Pain de mousse  EON Foam 6'6"SB moulés en France (Bretagne), lattage 3mm Plywood

Biomass ça veut dire quoi ?
Fabriqués à partir de polystyrène NEOPS® de KNAUF INDUSTRIES®, le naphta issu du raffinage du pétrole a été remplacé par un naptha végétal issu de la compression des végétaux : élagages publics et privés, rotations agricoles, débroussaillages, feuilles mortes, tontes amenées en déchetterie.
La mousse est également 100% recyclable via le réseau de retraitement Knauf Circular. 

Les billes de polystyrène sont agglomérées dans un moule proche du shape final sous haute pression, permettant une excellente résistance à la compression, une faible absorption d'eau et de résine lors de la stratification et une finition facilitée au ponçage par rapport au polystyrène conventionnel en blocs.

Pain de mousse  EON Foam 7'6"MALIBU moulés en France (Bretagne) non latté.

Biomass ça veut dire quoi ?
Fabriqués à partir de polystyrène NEOPS® de KNAUF INDUSTRIES®, le naphta issu du raffinage du pétrole a été remplacé par un naptha végétal issu de la compression des végétaux : élagages publics et privés, rotations agricoles, débroussaillages, feuilles mortes, tontes amenées en déchetterie.
La mousse est également 100% recyclable via le réseau de retraitement Knauf Circular. 

Les billes de polystyrène sont agglomérées dans un moule proche du shape final sous haute pression, permettant une excellente résistance à la compression, une faible absorption d'eau et de résine lors de la stratification et une finition facilitée au ponçage par rapport au polystyrène conventionnel en blocs.

Pain de mousse  EON Foam 7'6"MALIBU moulés en France (Bretagne), lattage 3mm Plywood

Biomass ça veut dire quoi ?
Fabriqués à partir de polystyrène NEOPS® de KNAUF INDUSTRIES®, le naphta issu du raffinage du pétrole a été remplacé par un naptha végétal issu de la compression des végétaux : élagages publics et privés, rotations agricoles, débroussaillages, feuilles mortes, tontes amenées en déchetterie.
La mousse est également 100% recyclable via le réseau de retraitement Knauf Circular. 

Les billes de polystyrène sont agglomérées dans un moule proche du shape final sous haute pression, permettant une excellente résistance à la compression, une faible absorption d'eau et de résine lors de la stratification et une finition facilitée au ponçage par rapport au polystyrène conventionnel en blocs.

Pain de mousse  EON Foam 9'4"MALIBU moulés en France (Bretagne), lattage 6mm Plywood

Biomass ça veut dire quoi ?
Fabriqués à partir de polystyrène NEOPS® de KNAUF INDUSTRIES®, le naphta issu du raffinage du pétrole a été remplacé par un naptha végétal issu de la compression des végétaux : élagages publics et privés, rotations agricoles, débroussaillages, feuilles mortes, tontes amenées en déchetterie.
La mousse est également 100% recyclable via le réseau de retraitement Knauf Circular. 

Les billes de polystyrène sont agglomérées dans un moule proche du shape final sous haute pression, permettant une excellente résistance à la compression, une faible absorption d'eau et de résine lors de la stratification et une finition facilitée au ponçage par rapport au polystyrène conventionnel en blocs.

Aerialite Volan 7534 6oz Fiberglass - 80cm Width

The WoodKit PRO Mini Simmons was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Retro Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Flying Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO 7 Seas was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Dream Catcher was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Spitfire  was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO One Mid was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO The Tanker was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Nexpa was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Rocket was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Kanaloa was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Murcielago was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Malibu was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Mini Fish was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Infinity was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Jiantou was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Spider was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Stiletto was designed by shaper David Weber and brings together everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- the board's skeleton, laser-cut from Surfply3L (100% Paulownia plywood)
- 8 planed Paulownia boards for the deck/bottom (150mm wide and 4mm thick)
- 10 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.
- Assembly instructions written by David Weber

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Basic includes everything you need to make your own Hollow surfboard out of Paulownia wood.

It includes:

- 8 planed Paulownia boards for the deck/bottom (150mm wide and 5mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

Optional:
- Plywood panels ( 5mm poplar ply or 5.5mm Surfply3L) for cutting out the frame
- CNC laser cutting of the skeleton from a 3D shape file

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Shape300 Gather everything you need to make your Hollow surfboard from Paulownia wood and make construction easier with the top/bottom panels already glued in 300mm.

It includes:

- 4 planed Paulownia boards for the deck/bottom (300mm wide and 5mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

Optional:
- Plywood panels ( 5mm poplar ply or 5.5mm Surfply3L) for cutting out the frame
- CNC laser cutting of the skeleton from a 3D shape file

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

The WoodKit PRO Custom Gather everything you need to make your Hollow surfboard from Paulownia wood and make construction easier with the top/bottom panels already glued in 600mm width.

It includes:

- The skeleton (FrameKit) laser-cut from your shape3D file using CNC technology
- Planed Paulownia panels for the deck/bottom (600mm wide and 6mm thick)
- 12 bendable Paulownia wood strips to form the rails of the board (10x10mm section)
- 5 Paulownia reinforcement blocks for the nose/tail and fin areas.

The kit is manufactured by iPaulownia using paulownia wood sourced from plantations in the Valencia region of Spain. Paulownia is a very lightweight wood (260-280 kg/m³) that is resistant to water, salt, and torsion. It is easy to work with and gives the board an aesthetically pleasing appearance.

Amber translucent pigment 30 g from West & Senior .
Designed for coloring polyester and epoxy resins , this high-quality pigment allows for transparent or semi-transparent effects while preserving the depth and gloss of the resin.

Thanks to its high concentration, a small amount of pigment is sufficient to obtain the desired intensity.
The dosage can be adjusted according to the desired effect, ranging from a light translucent tint to a more intense colouring while maintaining a transparent appearance.

Amber translucent pigment 250 g from West & Senior .
Designed for coloring polyester and epoxy resins , this high-quality pigment allows for transparent or semi-transparent effects while preserving the depth and gloss of the resin.

Thanks to its high concentration, a small amount of pigment is sufficient to obtain the desired intensity.
The dosage can be adjusted according to the desired effect, ranging from a light translucent tint to a more intense colouring while maintaining a transparent appearance.

Yellow Green translucent pigment 30 g from West & Senior .
Designed for coloring polyester and epoxy resins , this high-quality pigment allows for transparent or semi-transparent effects while preserving the depth and gloss of the resin.

Thanks to its high concentration, a small amount of pigment is sufficient to obtain the desired intensity.
The dosage can be adjusted according to the desired effect, ranging from a light translucent tint to a more intense colouring while maintaining a transparent appearance.

Yellow Green translucent pigment 250 g from West & Senior .
Designed for coloring polyester and epoxy resins , this high-quality pigment allows for transparent or semi-transparent effects while preserving the depth and gloss of the resin.

Thanks to its high concentration, a small amount of pigment is sufficient to obtain the desired intensity.
The dosage can be adjusted according to the desired effect, ranging from a light translucent tint to a more intense colouring while maintaining a transparent appearance.

Scarlet translucent pigment 30 g from West & Senior .
Designed for coloring polyester and epoxy resins , this high-quality pigment allows for transparent or semi-transparent effects while preserving the depth and gloss of the resin.

Thanks to its high concentration, a small amount of pigment is sufficient to obtain the desired intensity.
The dosage can be adjusted according to the desired effect, ranging from a light translucent tint to a more intense colouring while maintaining a transparent appearance.